Conducted emission test on LED light driver with EMI receiver

-

In order to carry out an emission test on an LED light driver that is also equipped with an EMI receiver, the following processes need to be carried out:

  • The first thing that needs to be done in order to get everything ready is to put the LED driver and the LED bulb inside of the EMI testing chamber. Following this step, connect the LED driver to the power source.
  • Calibration Ensure that the EMI receiver is calibrated in line with the instructions that were supplied by the manufacturer. Calibration
  • First switch on the LED driver, and after that is done, use the EMI receiver to take the measurement once it has been turned on. The EMI receiver is going to pick up and take readings of the conducted electromagnetic interference (EMI) that is being produced by the LED driver and the light.
  • Data Collection In order to do an analysis on the signal caused by conducted EMI, it is essential to gather data from the EMI receiver. Waveforms in the frequency domain, the amplitude domain, and the time domain should all be included in this data.
  • Conduct an analysis of the information you've acquired to determine whether or not the LED driver and light in issue are compliant with the EMC conducted emission laws that are in effect, and then submit your results.
  • Reporting: Compile a report that integrates the information collected from the EMI receiver and offers a succinct description of the test results.

It is essential to put LED light drivers through emission tests in order to verify that they are in compliance with the EMC requirements that are applicable and that they do not cause interference with any other electronic equipment. These tests must be performed in order to ensure that they do not interfere with any other electronic devices.

Comments

Post a Comment

Popular posts from this blog

-
Image
The ipx9k High Temperature Pressure Jet Waterproof Test Chamber is characterized by a waterproof grade of 9, indicating high temperature and high pressure water spraying, and spraying high temperature and high pressure water in various directions of the shell for water spraying test. In addition, k represents a function of pressurization, and under such strict conditions, its water pressure will become stronger. The ipx9 is currently a high level of waterproof protection. The IPx9 High Temperature Pressure Jet Waterproof Test Chamber is also widely used in fields such as LED lighting fixtures, display screens, household appliances industry, automobiles, and automotive accessories. At the same time, all dust and waterproof equipment can be customized according to user needs. The ipx9k High Temperature Pressure Jet Waterproof Test Chamber has four different vertical spray angles, namely 0 °, 30 °, 60 °, and 90 °, and the water pressure can reach 8000 to 10000 Kpa; Moreover, its testing r
Read more
-
Image
Capacitance  refers to the ability to hold a charge. It is a medium for realizing the storage and release of static charges, with the characteristic of permanent charge storage. Capacitor components are widely used in power supply filtering, signal filtering, signal coupling, resonance, filtering, compensation, charging and discharging, energy storage, and power separation in circuits. According to its ability to accommodate charges, it is generally measured in Farads, and the international unit is Farads. Therefore, capacitors are essential components for electronics and power. The role of capacitors: Bypass capacitors and decoupling capacitors are two devices that provide energy storage for local devices. Bypass capacitors can reduce load demand, make the output of the voltage regulator smooth, similar to a small rechargeable battery, and can be discharged and charged. The decoupling capacitor can smooth the edge signals of the device, so as to prevent the input signal from being too
Read more
-
Image
1 General 1.1 Scope and object This International Standard(IEC61032) specifies details and dimensions of test probes intended to verify the protection provided by enclosures with regard to: – protection of persons against access to hazardous parts inside the enclosure; – protection of the equipment inside the enclosure against ingress of solid foreign objects. SMT IP10T_AL The object of this International Standard is: – to bring together in one publication object probes and access probes currently specified in other standards, together with any necessary new probes;    – to guide technical committees in the selection of test sphere; – to encourage those concemed to specify test probes in accordance with those already specified in this International Standard rather than modify details and dimensions; – to limit the further proliferation of types of test probe. 1.2 General recommendations When selecting probes, priority should be given to IP code probes. The use of other probes, particul
Read more